Сделайте свою компанию и бизнес успешными

env manual gearbox

0
Голос за!

env manual gearbox

LINK 1 ENTER SITE >>> Download PDF
LINK 2 ENTER SITE >>> Download PDF

File Name:env manual gearbox.pdf
Size: 4335 KB
Type: PDF, ePub, eBook

Category: Book
Uploaded: 6 May 2019, 15:11 PM
Rating: 4.6/5 from 705 votes.

Status: AVAILABLE

Last checked: 15 Minutes ago!

In order to read or download env manual gearbox ebook, you need to create a FREE account.

Download Now!

eBook includes PDF, ePub and Kindle version

✔ Register a free 1 month Trial Account.

✔ Download as many books as you like (Personal use)

✔ Cancel the membership at any time if not satisfied.

✔ Join Over 80000 Happy Readers

env manual gearboxThe example below is from a Triumph and as you can see, includes a free wheel device. Sam This is from a C or perhaps Robin's J3. F1344 had a cross tube ENV box but didn't use the cross tube mountings, i think they were possibly just using up boxes left over from the C type production run. Cheers P The power of the internet The J3 had a standard J2 gearbox Rich Vintage MG Parts As Richard says, standard J gearbox in the J3. It's by coincidence that this ENV box picture I found on Google Images.Would the manual ENV MG gearbox have been fitted to a C-type originally. This following is just an academic question and perhaps it has never been looked into but, ignoring the freewheel device, are the components of these two ENV gearboxes in any way interchangeable. I can find no detailed information on either. Sam The gears in the ENV box are quite large. Your case looks somewhat smaller. Regards Rich Vintage MG Parts This ENV box is quite substantial and would have been used with a 2 litre Coventry Climax engine. Sam. It is worth noting that the original patterns used by ENV when making manual gearbox cases incorporated variations. One such variation relates to the apertures of the raised clutch inspection hatch area. If you are using an ENV manual gearbox which has either a plain case, AC or Invicta motif then please measure the hatch area before ordering as it may differ slightly to the standard MG size. We may be able to match up a cover for you if this is the case. Please note that the above inspection plate may be undersize when used on a preselector clutch housing. We now produce an oversize ENV inspection cover plate for this application. The above photo also shows an MG badge faithfully copied from an F Type gearbox with the wooden pattern made from 19 pieces of wood. We will manufacture another small batch on receiving the next order. We also supply Wellseal jointing compound. Price -- ?25 -- ENV manual gearbox inspection Plate - (fully polished) Price -- ?http://engin-otomotiv.com/fckeditor/userfiles/distortion-ds-1-manual.xml

    Tags:
  • env manual gearbox, env manual gearbox, env manual gearbox, env manual gearbox diagram, env manual gearbox transmission, env manual gearbox parts, env manual gearbox assembly, env manual gearbox.

25 -- ENV preselector oversize inspection Plate - (fully polished). Please upgrade your browser to improve your experience. And since the beginning of 2012 I have been offering a full repair and overhauling service for these gearboxes with my company pbm engineering. This website shows a range of work that I offer in respect of a part or full revision of your preselector-box. Once your gearbox has been delivered to me I compile a detailed status report by inspecting and, if necessary, partly disassembling the gearbox in order that I can make a precise cost estimate. (My suggestion: take some hours to deliver your gearbox yourself and be present when I do this please have in mind to arrange a time in advance). My invoice details all necessary work procedures and spare parts that have been built in, so it is easy for you to comprehend what work has been done. As additional proof you will get back the replaced parts, of course. This manual is deliberately not a hardback edition. Every page is removable and, in a protective plastic cover, may serve as an aid directly where needed: on the workbench. In addition, it contains some useful tips for DIY mechanics as well as a DVD with 34 construction drawings to manufacture special tools, some of which are indispensable assistants when repairing the gearboxes. On the DVD you also will find more than 280 restored original blueprints and a range of drawings created by the author himself. They will aid you in remanufacturing many parts that are no longer available.I think that every person owning an automobile with the ENV transmission should have a copy, whether he intends working on the gearbox or not. This meant that non-rotating brake bands could be used for the parts which are subject to wear, which results in a simpler design than a rotating component such as a typical clutch.http://germanlanguagecircle.com/userfiles/distressor-el8x-manual.xml The wearing components could also be mounted on the outside of the mechanism (rather than buried within it), providing easier access for maintenance and adjustment.Walter and one of the co-owners of Armstrong Siddeley Motors formed the Self-Changing Gears Ltd.On other cars, the gear change pedal functioned like a clutch when starting from a standstill. This was owing to the sporting, or indeed racing, market for the Wilson gearbox, so that the ratios could be more closely spaced.The brake band to be selected was controlled by a rotating cam, moved by the gear shift lever. Only one band was engaged for each gear selection. This small hand-operated lever could not provide enough power to engage and lock the brake band, thus the need for the foot pedal. If the cam (for each gear) held the linkage in place, rather than allowing it to swing out of the way, the busbar finger would then press, via the operating strut, onto the toggles controlling the brake bands themselves. These toggles provided the additional leverage necessary to hold the brake band in place, under the force of the coil spring, until the pedal was next pressed. A further characteristic of the Wilson design was the use of self-adjusting nuts on each band, to compensate for wear.There was no mechanical servo action, so no need for the Wilson's cam or toggle arrangements and the change gear pedal.The shift mechanism was hydraulic, to reduce driver effort. Clutches were used in combinations, allowing many more ratios than actuators. There were three hydraulic cylinders, each with two positions and controlling dog clutches for gear trains arranged on four shafts. The cylinders were controlled by a rotary valve on a simple quadrant gear lever and activated by pushing the lever sideways into its gate.It operates as a number of separate gearboxes, each one controlled by a separate clutch, interlocked to avoid multiple selection. Selecting a gear is a matter of selecting the appropriate clutch.https://www.informaquiz.it/petrgenis1604790/status/flotaganis09062022-1030 An advantage of this type is that it's simple to arrange remote operation, as there is no gear shift linkage as such, merely duplication of a clutch linkage.The advantage of this arrangement was its use of four clutches, all easily serviced from outside the engine assembly, without needing to remove the engine. The clutches were multi-plate oil-supplied wet clutches. The first gearboxes gained a reputation for unreliability and in 1985 the original developers, Brockhouse, licensed them to Avon Maxwell Transmissions. This acted as a 50 hp hydraulic retarder.This combines the simplicity of a shifting gearbox with the rapid shifts of a clutch-based design. There are effectively two separate gearboxes, each offering alternate ratios from the overall set, and the two clutches select which gearbox is in effect. Changes within the gearbox are done automatically, to predict which ratio the driver will require next. Provided that the next ratio has been selected correctly (i.e. the computer guessed correctly as to an up-shift vs.Unexpected shifts may confuse the system though and it must first select the correct ratio before engaging the clutch, giving a far slower shift.Please help improve this article by adding citations to reliable sources. Unsourced material may be challenged and removed. ( February 2020 ) ( Learn how and when to remove this template message ) On starting, just the accelerator pedal was pressed, with the eventual shift into third gear made by simply pressing the gear change pedal.Grenville Publishing.Archived from the original on 5 March 2016. Retrieved 30 January 2009. Crowood Press. ISBN 1-86126-400-3.The Devil's Chariots. Sutton. ISBN 0-7509-4152-9.By using this site, you agree to the Terms of Use and Privacy Policy. Construction of the Regis Body. Gallery 1 Gallery 2 Gallery 3 Gallery 4 Gallery 5. Gallery 6 Chassis List Handbook Instruction Manual Specification. Electrical Wiring Information Bendix Braking System. ENV Type 75 Preselector Gearbox.https://duluthtaxiservice.com/images/compaq-evo-d510-cmt-user-manual.pdf ENV Type 75 Gearbox Manual. Other cars I have owned. ENV Preselector Gearbox. Introduction: Peter Meyer in Germany has now made his new book on th e ENV Type 75 gearbox available and is definately recommended to users wishing to become familiar with maintaining this type of gearbox. To buy a copy, he can be contacted at: www.preselector-gearbox.de NOTE: Please see Gallery - ENV Gearbox for the full ENV Instruction Manual pages. The majority of Regis cars were fitted with preselector gearboxes allied to a centrifugal clutch connecting the gearbox to the engine. It was appreciated at the time that the gearbox was a heavy unit and reduced the performance of the 10hp cars so that the six cylinder, 12hp version was introduced to achieve a better performance and top speed. The epicyclic gearbox with sun wheels, planet wheels and annulus gears has been in existence from almost the beginning of motoring history. This type of gearbox had all the gears in mesh and the operation enabled gear changes to be made without any crashing of gears. The ordinary, “crash” gearbox was the norm and yet, since it required the adroit changes of gear with the correct revs of the engine allied to the road speed, few drivers of the time were able to change gear without a noisy exchange. In due course, the synchromesh manual gearbox was introduced from America and this enabled manual changes without the noise associated with the “crash” box. The synchromesh gearbox is much lighter than the preselector box and enabled better power to weight ratios for improved performance, especially on the smaller engined cars. By this time, the modern automatic gearbox, based on the epicyclic principle, had become a popular replacement. With the preselector box, changes were smoothly made with the press of the left-hand gearchange pedal. This pedal was not a clutch pedal since it changed gear only. The clutch was usually an automatic, centrifugal unit where the increase of revs brought the clutch together so that it did not slip once the car had moved from rest. On some cars, Daimlers and a few Armstrong Siddeley cars of the mid-thirties, the fluid flywheel was fitted. However, on some cars, including some of the earlier Crossley Tens, no clutch was fitted at all and starting from rest required the gearchange pedal to be used like a normal clutch since starting used the slipping of the first gear band as a starting medium. Many drivers of preserved cars with preselector gearboxes find it difficult to get used to the gearbox. In order to use the box when fitted with a clutch, first gear is selected and the pedal pressed and released. First gear is now engaged but the car is stationary since the clutch is disengaged at idling speed. When the accelerator is pressed, the clutch begins to take up and the car starts to move forward and second gear can be selected and engaged with the pedal as the car moves faster. Each gear can be selected once the previous gear is engaged so that when ready, the selected gear can be engaged. Once driving in top gear, third gear can be selected ready for when the car has to be slowed and third gear engaged. The next gear needed can be selected at any time ready to be engaged. This is preselection. The following notes are taken from ENV Engineering notes on their preselector gearboxes, including the driving notes from the first Section of the ENV Gearbox Instruction Manual. Notes from ENV Engineering Co Ltd, Makers of the Regis gearbox to Wilson Patents. (Gearbox Type 75.): ADJUSTMENTS: NOTE: All adjustments should be made with the engine stationary. CHECKING THE SELECTION (of a gear): Should any gear persistently fail to engage, it will probably be caused through a derangement of the selector control mechanism. To check this, detach the adjustable rod connected to the selector lever on the gearbox. Set the lever on the gearbox to first gear position, taking care to see that the lever is properly located by the ball detent. Set the hand lever into the first gear position and adjust the length of the connecting rod to suit. Provided that the gear detents have not been changed, the selector lever should now move through each gear with the gearbox lever locating in each gear detent. All joints in the linkage should be checked for looseness or backlash. CHECK OVER PEDAL CLEARANCE: It is essential that there should be a definite clearance between the pedal and the floorboards when the pedal is fully depressed and that the lever on the box is moved to its extreme position, coming up as it should do against the stop situated inside the gearbox. Should the pedal touch the floorboards on depression, it is then necessary to shorten the connecting rod between the pedal and the lever on the gearbox. The pedal must also have at least one quarter of an inch clearance on the upward stroke in every gear and it will be found that the pedal returns further both in first and reverse gears, allowance should be made for the full stroke of the pedal in both these gears. Select the gear and with the engine stationary, actuate the pedal about two dozen times to allow the automatic adjustment to take to the new setting. ADJUSTMENT TO OVERCOME SLIPPING: Slipping could occur for three reasons:- That the automatic adjustment is failing to take up. This can be determined by:- Removing the top inspection cover of the gearbox and selecting and engaging the speed required. If the wedge-shaped plate on top of the control mechanism strikes the “v” shaped set screw on the band and is moved an appreciable amount, then the automatic adjuster should work by actuation of the pedal. To test this, make a pencil mark on the thimble nut, actuate the pedal briskly two dozen times and note if it has moved at all. If the adjuster ring is being moved a reasonable amount with each stroke of the pedal and the mark on the nut does not turn, change the adjuster nut spring and repeat the “pumping action.” The automatic adjuster should only work if the wedge-shaped plate is turned an appreciable amount on striking the set screw. Insufficient toggle action:- The remedy is to screw in the “V” shaped adjuster screw on the band of the speed to be adjusted to the extent of about one turn. STICKING IN TOP GEAR: Should top gear fail to disengage immediately the pedal is depressed, this is probably caused by high spots in the fabric lining and the cone should be re-bedded. This is effected by selecting top speed with the car stationary and the handbrake on and running the engine to 1500 rpm. The gearchange pedal should be let back sufficient to reduce the engine speed to about 500rpm but not enough to stall the engine. This treatment must not be carried out too long but should be repeated several times (if required) with short intervals to prevent overheating. Drawing the oil and refilling the gearbox may be tried. IMPORTANT INSTRUCTION WHEN TOWING: In the event of the car breaking down and having to be towed more than two or three miles, the propeller shaft flange should be first disconnected from the rear axle end when no clutch is fitted between the gearbox and engine. The reason for this is that the oil pump is driven from the input shaft of the gearbox, consequently if the car is towed for some distance, the proper supply of oil will not be available to the gears which might cause consequential damage. These instructions end with the requirement to return a damaged gearbox to the manufacturers for expert repair. The following notes are taken from the: “INSTRUCTION BOOK of the E.N.V. PRE SELECTIVE GEAR BOX ( WILSON PATENTS) Section 1. HOW TO OPERATE THE GEARS: Before starting the engine make certain that neutral is engaged which is effected by selecting neutral and pushing the operating pedal out fully to the end of its travel so as to make sure that nobody has pre-selected a gear and simply put the gear lever back to its neutral position. Do not race the engine in neutral. To obtain first gear, the gear lever should be put into the notch on the quadrant or gate, whichever is employed. The gear operating pedal should be fully pressed down then let back gently and the accelerator pedal should be operated in the normal way. While the car is moving on first gear, the lever should be put into the second speed notch and the pedal operated as before and each and every successive gear should be selected and engaged until top speed notch is reached. It is advisable if one is driving in traffic, immediately to pre-select third gear so that in the event of having to slow down, it is possible simply by the action of the pedal to engage the lower gear without delay. The reverse, first, second and third speeds are operated by contracting bands; on top gear, however, a cone clutch is employed. ACTION OF THE OPERATING PEDAL: The gear operating pedal has two movements, viz., a slight amount of pressure on the pedal will be sufficient to slacken off the brake bands but is not sufficient to disengage the selected struts of the gearbox. The first movement will give free engine position. However, when the pedal is fully depressed, the selected strut is caused to come out of action and whichever gear is pre-selected will then come into operation. It will be immediately obvious to anyone using a Wilson Box for the first time, that as soon as the gear engaging pedal is pressed down and is allowed to return, there is a spring action inside the gearbox. The only function of the gear operating pedal is actually to compress this spring and on letting the pedal up, spring pressure is again applied: It stands to reason that the pedal should be let back with care in exactly the same manner as an ordinary clutch. The combined action of the pedal and spring causes a part known as the “busbar” to move up and down and the action is very similar to the operation of an ordinary external contracting brake, the busbar being similar to the brake operating lever which moves to and fro. The busbar causes the brakes to contract on the drum through the action of the operating struts. AUTOMATIC ADJUSTMENT: The only difference in the simile is, that with a brake it is necessary to take up the wear that takes place in the linings, by tightening the adjustment by hand; in this type of box, it is taken care of automatically. The movement of the operating pedal causes a certain part of the gearbox known as the “adjuster nut” to rotate. Thereby adjusting the brake bands and taking care of wear. Care should be exercised not to “slip” the brakes or clutch unnecessarily. The pedal should be definitely pushed out sufficiently far to disengage the gear and instead of slipping it, a lower gear should be engaged, so that the engine will drive the car at whatever speed is necessary. Any undue slipping that takes place will cause excessive wear on the brake linings. HOW TO OVERCOME INITIAL WEAR: When the car is new, it stands to reason that the automatic adjustment of the brake bands will need to operate more than when the bands have thoroughly bedded in. It may be found that the amount of initial wear of compression of the liners will not be taken care of by normal rotation of the automatic adjustment. It is possible to cure temporary slipping by pushing the operating pedal fully in and out with a pumping action of the pedal. DRIVING HINTS: When changing into a higher gear, it is always necessary to allow the operating pedal to return to the fullest extent of its travel before accelerating. There should be a momentary pause after the engaging pedal has been released, before the accelerator pedal is pressed down hard. The bands or clutch have to obtain a firm grip, as well as to expel the oil between the friction surfaces. When changing down normally from a high to a lower gear, there is no necessity to take the foot off the accelerator pedal. It would not, however, be wise to preselect and engage first or second gear while the car is running at a speed higher than could normally be obtained on either of these gears. Should the pedal return without engaging a gear make certain the gear is selected properly and depress and release the pedal again. LUBRICATION: Finally, we come to the question of lubrication. Examination of the gearbox will show it is provided with a brass cap through which the lubricating oil can be inserted, considerably above the level of the shaft. There is a definite level in the gearbox above which it should not be filled. This is controlled by a level plug on the side of the box so that before attempting to replenish the box, it is necessary to remove the level plug in order to obtain the correct quantity of oil in the box and allow sufficient time for the oil to find its level. Apart from this attention the driver does not have to worry. A pump is provided in the box and is situated in the front end of it, which automatically supplies the gears, shafts and the whole of the internals of the box with a constant stream of oil, assisted by centrifugal action. SUGGESTED MODERN OILS: The following information is not a part of the ENV document since out of date oil recommendations would appear to be useless for the modern owner. Castrol PGSE oil (“preselector gearbox oil”) is a modern oil specifically made for these gearboxes. It is available in bulk in 20 litre or 240 litre drums since most users are bus operators nowadays, using preselector or pneumocyclic boxes, both based on the epicyclic principle. Note: A user of PSGE in France who used these pages to assist in work on a preselector gearbox was informed by Castrol Oils, UK that modern Castrol TQD has the same specification as PSGE oil. Check with your Castrol dealer on this matter. If unable to obtain this oil, a straight oil ( that is, not a multigrade oil) of SAE 30 or 40 would be acceptable. Modern multigrade oils are not used in these boxes since their “slippery” attributes are not compatible with the linings gripping the drums in the preselector boxes. The Following notes are from ENV in connection with rebuilding a Type 75 gearbox. (They were sent to the Author in 1965 from an enquiry to ENV Ltd.) To Dismantle: 1 Remove the top cover and undo each automatic adjuster nut three or four turns. Now remove the pump plunger and oscillating cylinder, next the pump housing. Note the position of the three coil springs for assembly. If tight it can be extracted by using a plate and the two holes used by the two cheese-headed screws of the front cover; but first remove the input shaft; take care of the steel balls which will come away when this ring is removed. 3 Remove gearing: The running gear can be removed piece by piece noting carefully the location of the various planetary trains; bushes, shims, etc. To remove the reverse and last annulus, this should be driven out from the rear and after having first removed the output shaft from the rear end. 4 To remove the gear case from the bottom cover. Remove all the nuts fixing the bottom cover to the case, also extract all the long studs, numbering eight. This depresses the busbar and enables the case to be removed. This will ensure that the end does not burr when used since the busbar spring is very strong and can damage the end of the stud if used several times. Withdrawing the damaged stud will damage the screw thread within the aluminium base requiring the thread to be tapped to a larger size for future use and a larger plug made for the new thread to block the hole. (This information is not part of the ENV instructions.) All the bands and busbar can be removed from the bottom cover. Before removing the spring tension nut from the busbar, note carefully the number of washers between the end of the nut and the split pin hole. The correct quantity should be replaced when renewing the busbar. 5 TO RE-ASSEMBLE: The case is placed in position over the finished bottom cover and as no paper joints are fitted a good jointing compound should be used. See that the two dowels locate then tap the case into position with a hide mallett, refit the eight long studs, replace all the eighteen nuts and tighten up. NOTE: When installing the gear train, ensure that the input (Front) and output (Rear) shafts can be turned independantly of each other during initial assembly and check again once the oil pump and front cover have been fitted. Failure to do this may mean that the gearbox will be stuck in top gear! 6 To replace running gear: This is best assembled complete on the bench after first having removed the output shaft rear end ball race. The whole mass can now be pushed through the case, steadying the rear and with the output shaft and a steady pressure put on the input shaft to ensure that the ball race fitted to the rear annulus goes well home into its housing. It is now best to tip up the back of the box so that the front cover can be put on working from the top, taking care that the output shaft does not slip out of place. Should there be any difficulty in replacing the running gear, remove the speedo pinion as this might not mesh with the wheel on the output shaft. The outer actuating ring can now be replaced, locating the two dowels on the 4th speed actuating support, the two countersunk scres replaced and tightened up. Make the hook of the top speed pull rod; now drop in the steel balls into their respective slots, replace the pump housing and see the three springs are hooked on correctly; now return the pump plunger and cylinder. 7 The front cover can then be replaced using jointing compound tighten up the eleven outer nuts, the five nuts of the pump housing studs, the two cheese-headed setscrews. All that is now required is to re-adjust the automatic adjuster nuts to within one turn of the correct adjustment, the remainder should be pedalled up to ensure the correct working of the automatic adjuster springs.To refit new bands: Great care should be taken in the fitting of the new bands to ensure that the centralisers take up their correct position. Reverse Band: See that the centraliser is fitted to band lug correctly, i.e: that the small tit on centraliser is to the top. Next fit band to bottom cover and contract the band on to one of the annuli, using the strut gear and dbusbar. When band is fully engaged force the centraliser round so that it comes into contact with the facing on the bottom cover, this gives the correct position when the band is off. Forward Band: See that the correct off and near centralisers are fitted then proceed to contract the band as in reverse. When this is done, force the near side centraliser up to the busbar support and the offside down to the facing on battom cover. Do this with all three forward bands and they will then be centralised properlu in their off position. INSPECTION OF PARTS AND GEARBOX WHEN DISMANTLED: Busbar: If it is found that the operating pad on the busbar is worn, replace it with spare busbar supplied. Brake Drums: If grooves on brake drums are seriously damaged, we would recommend you clean up the grooves with a pointed tool NOTE: These grooves are not screwed but are parallel annular grooves. Lubrication: See notes elsewhere in this section about oil and ensure that Castrol PSGE oil is used and changed regularly.: PRESELECTOR GEARBOX: ON ROAD PROBLEMS: (Not part of the Official instructions but from experiance on the road!) The preselector gearbox is an extremely reliable unit which will continue to operate reliably for many thousands of miles. Depending on its usage, over 300,000 miles (or 480,000 kilometres) can be obtained provided only that the oil is changed at the specified intervals and the gearbox is correctly used. This latter really only requires that the gearchange pedal is allowed to return smartly so that the required gear engages and does not slip. Even so, very high mileages are possible with care. The oil must be changed every 3,000 miles and checked for level as required. Initially, new gearboxes should have the oil changed after 1,000 miles and every 3,000 thereafter. The original recommended oils were basically engine oils of 30 or 40 SAE rating but modern oils are much improved so that modern preselector gearboxes have recommendations to change every 5,000 miles. However, many cars will be used for relatively low mileages so that a change of oil annually might be best when a car has not reached 3,000 miles in the year. The owner is in the best position to decide, based on the change intervals mentioned. It is suggested that enquiries be made to Castrol Oils who make the PSGE oil in connection with intervals of oil changes with modern oil. Owners of cars with these gearboxes may not be aware of the adjustments that can be made to the gearbox and will rely on a local mechanic who may not be totally au fait with the gearbox. If adjustment of the bands is not maintained then the pull rod on the adjuster may become slack on the band. Sometimes, before this is noted and rectified, engaging the next gear may well give an apparent “neutral”. This is because each strut has an interlock pad on its outer face. This is designed to prevent two gears being engaged at the same time when very excessive damage could be done.